Cameras, lenses and mirrors

From AIRWiki
Revision as of 18:43, 21 December 2015 by AndreaBonarini (Talk | contribs) (List of Cameras)

Jump to: navigation, search

IMPORTANT NOTES

Never touch the sensor element (CCD or CMOS) of a camera with anything! It can very easily be scratched.

Never touch the glass elements of a lens with your hands! The oil from human skin will cause damage.

Cameras

In the AIRLab you can find different kind of cameras. These are the main groups:

  • Analogue cameras. Video output is given as an electrical signal, which needs analogue-to-digital conversion to be processed by a computer; this is done by a specific card called frame grabber or video capture card (the latter tend to be the lowest-performance items; see Cameras, lenses and mirrors#Frame grabbers for details). Analogue video is outdated for computer vision and robotics applications, due to its cost, low performance and complexity; nowadays digital camera systems (such as all the ones listed below) are always preferred.
  • USB cameras. Usually very cheap, they are suitable for low-performance applications (i.e. those where low frame rate is needed and low image quality can be accepted). Their main advantage (along with cost) is the fact that every modern computer has USB ports. The fact that the USB standard includes 5V DC power supply lines helps simplifying camera design and use.
  • FireWire cameras. The FireWire (or IEEE1394) bus is generally used for low-end industrial cameras, i.e. devices with technical characteristics much superior to those typical of USB cameras but low-performance according to typical machine vision standards. Industrial cameras usually give to the user a much wider control over the acquisition parameters compared to consumer cameras, and therefore they are usually preferred in robotics; their downside is the higher cost. There are different versions of IEE1394 link (see http://en.wikipedia.org/wiki/Firewire for details), with different bitrates, starting from the 400Mbit/s FireWire 400. Generally they are all considered superior to USB 2.0, even if theoretical bandwidth is lower for FireWire 400. Firewire ports can include power supply lines, but some interfaces (and in particular those on portable computers) omit them. Although the use of FireWire interfaces has expanded in recent years, they are not yet considered a standard feature for motherboards.
  • GigE Vision cameras. GigE Vision (or Gigabit Ethernet Vision) is a rather new connection standard for machine vision, based upon the established Ethernet protocol in its Gigabit (i.e. 1000Mbps) version. It is very interesting, as complex multiple-camera systems can be easily built using existing (Gigabit) Ethernet hardware, such as cables and switches. Vision data is acquired simply through a generic Ethernet port, commonly found on motherboards or easily added. However, 100Mbps (or fast Ethernet) ports are not guaranteed to work and can sustain only modest video streams; on the other hand, 1000Mbps ports are now standard on motherboards, so this will not be a problem anymore in a few years. It seems that GigE Vision is becoming the most common interface for low- to medium-performance industrial cameras.
  • CameraLink cameras. Cameralink is a high-speed interface expressly developed for high-performance machine vision applications. It is a point-to-point link, i.e. a CameraLink connection is used to connect a single camera to a digital acquisition card (frame grabber). Its diffusion is limited to applications where extreme frame rates and resolutions are needed, because CameraLink gear is very expensive.
  • ST Camera boards. Cameras with cell phone sensor and ARM processor for onboard computation.
  • Pixy Is a fast vision sensor that can be quickly “teached” to find objects, and it connects directly to Arduino and other controllers. Pixy processes images from the image sensor and only sends the useful information (e.g. purple dinosaur detected at x=54, y=103) to the microcontroller. The information is available through one of several interfaces: UART serial, SPI, I2C, digital out, or analog out. So Arduino or other microcontroller can talk easily with Pixy and still have plenty of CPU available for other tasks. (For more details see: Official web site and the web page that contains all the drives and guides: Project info)

The following is a list of the cameras available in the AIRLab. (To be precise, it is a list of the cameras that are modern enough to be useful.) For each of them the main specifications (and a link to the full specifications) are given. Details on the different types of lens mount are given below in Cameras, lenses and mirrors#Lenses. The 'how many?' field tells if multiple, identical items are available. Finally, the 'where?' field tells you in which of the AIRLab sites (listed in The Labs) you can find an item, and the 'project' field is used to specify which project (if any) is using it.

Ah, one last thing. People like to actually find things when they look for them, so don't forget to update the table when you move something away from its current location. If you don't know where you are taking it, just put your name in the table.

List of Cameras

resolution B/W, color max. frame rate sensor size interface maker model lens mount how many? where? project link to full specifications and/or manuals
1628x1236 B/W 24fps 1/1.8" CameraLink Hitachi KP-F200CL C-mount 1 DEI media:KP-F200-Op_Manual.pdf
752x480 color 70fps 1/3" GigE Prosilica GC750C CS-mount 3 Lambrate (2/3),
S05 (1/3) Andrea Romanoni
[1]
659x493 color 90fps 1/3" GigE Prosilica GC650C C-mount 1 Lambrate [[2]
1024x768 color 30fps 1/3" GigE Prosilica GC1020C C-mount (una ha l'anello C da spostare, altrimenti non va a fuoco e con attacco C si ROMPE!!!) 2 Lambrate (1/2)

in prestito a Domenico G. Sorrenti per demo Monza 19/11/12

[3]
CCIR (625 lines) B/W CCIR (50fps, interlaced) 2/3" analogue Sony XC-ST70CE C-mount 2 DEI (2/2) media:XCST70E_manual.pdf
659x494 color 30fps 1/4" FireWire 400 Unibrain Fire-i 400 industrial C-mount 3 Lambrate (3/3) RAWSEEDS (3/3) http://www.unibrain.com/Products/VisionImg/Fire_i_400_Industrial.htm
659x494 color 30fps 1/4" FireWire 400 Unibrain Fire-i board camera proprietary 8 Lambrate (3/8), Bovisa (2/8), User:PaoloCalloni (1/8), User:DavideMigliore (1/8), User:CristianoAlessandro (1/8),

presa 1 a fine febbraio10 con lente wide (quella di riserva di robocom), montaggio "a la rizzi" con lastrine di plexiglass e pezzo di profilato item User:Domenicogsorrenti (1/8)

RAWSEEDS (2/8), MRT (?/8)

queste sono quelle "nuove"? se si una e' su rabbiati, portiere di mrt, sin da cuvio, e' nella testa omnidir Domenicogsorrenti 21.04.09

1 nuova e' la frontale di recam

1 nuova sulla testa omnidir di ridan

http://www.unibrain.com/Products/VisionImg/Fire_i_BC.htm
640x480 color 30fps 1/4" FireWire 400 Unibrain Fire-i digital camera fixed optics (4.3mm, f2.0) 4

1 e' sulla testa omnidir di rigo

1 e' sulla testa omnidir di recam

1 e' sulla testa omnidir mrt05-03 (armadio domenico@unimib)

1 e' sulla testa omnidir mrt05-04 (armadio domenico@unimib)

http://www.unibrain.com/Products/VisionImg/Fire_i_DC.htm
640x480 dual sensor, 9cm baseline color 30fps 1/3" FireWire 400 Videre Design STOC stereo-on-a-chip stereo camera C-mount, fitted with two 3.5mm, f1.6, 1/2" lenses 1 Lambrate => li lin office => Domenicogsorrenti 13.01.09 => giulio fontana 23.01.09 http://www.videredesign.com/vision/stoc.htm
640x480 color 60fps 1/3" FireWire 400 Videre Design DCSG (associated with STOC) C-mount, fitted with one 3.5mm, f1.6, 1/2" lens 1 Lambrate http://www.videredesign.com/vision/dcsg.htm
? color 30 fps 1/3.8 inch optical format ? ST Microelectronics ST1-Cam + ST2-Cam integrated 2 ST1-Cam (STLCam (ST LEGO Camera)) (with Anil until 15.10.2010) Anil Koyuncu, ST2-Cam Lorenzo Consolaro and Dario Cecchetto ST1-Cam RunBot: a Robogame Robot Media:Cameradatasheet.pdf,‎Media:Rvs-v1-0.pdf‎, Media:RVS_Datasheet_v2.1.pdf‎ ,http://www.danielecaltabiano.com/wwme/ST-SW/st-sw.htm, ‎Media:Cam_pin_map.pdf
? color 30 fps 1/3.8 inch optical format ? ST Microelectronics RVS2-Cam integrated 1 AIRLab Lambrate (armadio prosilica) ? Media:Cameradatasheet.pdf,‎Media:Rvs-v1-0.pdf‎, Media:RVS_Datasheet_v2.1.pdf‎ ,http://www.danielecaltabiano.com/wwme/ST-SW/st-sw.htm
? color ? ? ? ST Microelectronics ST5-CamMic + ST6-CamMic integrated with microphone 2 ST5-CamMic Andrea Bonarini, ST6-CamMic AIRLab per E-2? ST6-CamMic E-2?
? color ? ? ? ST Microelectronics ST4-DC (Demo board) integrated 1 Raffaele Petta
? color ? ? ? ST Microelectronics ST5-CamMic + ST6-CamMic integrated with microphone 2 ST5-CamMic Andrea Bonarini, ST6-CamMic AIRLab per E-2? ST6-CamMic E-2?
? color 30 FPS ? USB 2 ? Microsoft Kinect ? 1 Cristian Mandelli, Deborah Zamponi July/August 2011 [E2? A robot for exhibitions] Pixy ? 1 Usert:TommasoMassari,December 2015 [Trash Bin]


Lenses

Be aware that sensor dimension (i.e. its diagonal, measured in fractions of an inch) is not the same for all cameras. Therefore one of the key specifications for a lens is the maximum sensor dimension supported. If you use a given lens with too big a sensor, the edges of the image will be black as they lie outside the circle of the projected image. Also beware of the strange convention used for sensor diagonals, i.e. a fraction in the form A/B" where A and B are integer or non-integer numbers. For instance an 1/2" sensor is smaller than an 1/1.8" one. The variability of sensor dimensions has another side effect: the same lens has a different angle of view if you change the sensor size. Therefore the same lens can behave as a wide-angle with a large sensor and as a telephoto with a small sensor.

An useful guide to lenses (in Italian or English) can be found at http://www.rapitron.it/guidaob.htm.

The following is a list of the actual lenses available in the AIRLab. For each of them the main specifications (and a link to the maker's or vendor's page for full specifications) are given. A '?' means an unknown parameter: if you know its value or experimentally find out it when using the lens (e.g. the maximum sensor size), please update the table before the information is lost again! Lenses having 'M12x0.5' in Column 'mount type' are only usable with Unibrain's Fire-i board cameras. A 'YES' in the 'Mpixel' column indicates a so-called Megapixel lens, i.e. a high quality, low-distortion lens designed for high-resolution industrial cameras (typically having large sensors); please note that some of these are specifically designed for B/W (i.e. black and white) cameras. The 'how many?' field tells if multiple, identical items are available. Finally, the 'where?' field tells you in which of the AIRLab sites (listed in The Labs) you can find an item, and the 'project' field is used to specify which project (if any) is using it.

Ah, one last thing. People like to actually find things when they look for them, so don't forget to update the table when you move something away from its current location. If you don't know where you are bringing it, just put your name in the table.

C-mount and CS-mount lenses

Industrial cameras usually have interchangeable lenses. This allows for the choice of the lens that is more suitable to the considered application. There are two main standards for industrial camera lenses: C-mount and CS-mount. Both are screw-type mounts. CS-mount is simply a modified C-mount where the distance between the back of the lens and the sensor element (CCD or CMOS) is shorter: therefore a CS-mount lens can be mounted on a C-mount camera if an adapter ring (i.e. a distancing cylinder with suitable threads) is placed between them. It is impossible, though, to use a C-mount lens on a CS-mount camera: if you try you will almost certainly break the sensor, scratch the lens, or both. Just because a lens fits a camera, it doesn't mean it can be actually mounted on it!

focal length max. aperture max. sensor size mount type maker model Mpixel how many? where? project link to full specifications
3.5mm f1.4 ? C-mount ? ? ? 1 Lambrate LURCH ?
4.0mm f2.0 1/2" C-mount Microtron FV0420 YES (B/W only) 2 Lambrate http://www.rapitron.it/obmegpxman1.htm
2.3mm f1.4 1/3" CS-mount Goyo 08-gm123142 ? 1 Bicocca ( Domenico G. Sorrenti da 19/11/12) rawseeds datasheet[[4]]
4.5mm f1.4 1/2" C-mount ? ? ? 1 DEI ?
4.8mm f1.8 2/3" C-mount Computar M0518 NO 1 DEI http://www.computar.com/cctvprod/computar/mono/048.html
6mm f1.4 ? C-mount ? ? ? 1 Lambrate (?) ?
6mm f1.4 1/2" C-mount Goyo GMHR26014MCN YES 4 Lambrate 2 nell'armadio + 2 scatole vuote http://www.goyooptical.com/products/industrial/hrmegapixel.html
8mm f1.4 ? C-mount ? ? ? 1 DEI ?
8mm f1.4 2/3" C-mount Goyo GMHR38014MCN YES 2 Lambrate http://www.goyooptical.com/products/industrial/hrmegapixel.html
8.5mm f1.3 2/3" C-mount Computar ? ? 2 DEI (old model)
12mm f1.8 2/3" C-mount ? ? ? 2 1 Lambrate + ? DEI
12mm f1.4 2/3" C-mount Goyo GMHR31214MCN YES 2 Lambrate http://www.goyooptical.com/products/industrial/hrmegapixel.html
15mm f2.0 2/3" C-mount Microtron FV1520 YES 1 Lambrate http://www.rapitron.it/obmegpxman1.htm
6-15mm f1.4 ? C-mount ? ? ? 1 Lambrate ?
12.5-75mm f1.8 ? C-mount ? ? ? 1 DEI ?


M12 lenses

We also use M12 lenses. These lenses are very simple, with no iris, and very small. Their mounting system is an M12x0.5 metric screw thread. They are commonly used for webcams, and usually do not provide the top optical quality.

focal length max. aperture max. sensor size mount type maker model Mpixel how many? where? project link to full specifications
2.1mm f2.0 1/4" M12x0.5 Unibrain 2042 NO 6

1 e' a bovisa nelle mani di marcello

1 e' a lambrate su un giano riusato come robowii

1 e' a bovisa sulla frontale del triskar recam

1 e' in mano a martino per fare una frontale => 06.05.09 E' in bovisa montata sul triskar #3

1 l'ha Davide Migliore per acquisizioni monoslam

1 e' sulla testa omnidir di rabbiati

Domenicogsorrenti 04.05.09

MRT midsize, robowii, monoslam http://www.unibrain.com/Products/VisionImg/Fire_i_BC.htm
4.3mm, no IR filter f2.0 1/4" M12x0.5 Unibrain 2046 NO 1 Lambrate (1/1) http://www.unibrain.com/Products/VisionImg/Fire_i_BC.htm
4.3mm f2.0 1/4" M12x0.5 Unibrain 2043 NO 3 Bovisa (1/3), Lambrate (2/3) http://www.unibrain.com/Products/VisionImg/Fire_i_BC.htm
8mm f2.0 1/4" M12x0.5 Unibrain 2044 NO 1 Lambrate (1/1) http://www.unibrain.com/Products/VisionImg/Fire_i_BC.htm


Frame grabbers

As previously said, a frame grabber is an electronic board that connects to one or more cameras, and converts the signals from the cameras into a data stream that can be elaborated by a computer. They are usually designed as expansion boards to be fitted into the computer case. Frame grabbers are necessary for analogue cameras (as they include the analogue/digital converters) or for CameraLink digital cameras (in this case the frame grabber is essentially a high speed dedicated digital interface). Other kinds of digital cameras don't need a frame grabber: this is one of the main advantages of digital cameras over analogue ones in machine vision applications, where the processing is almost always performed by computers. In the AIRLab two models of frame grabber are available:

All the frame grabbers (except the one on the MO.RO.1) are currently in AIRLab/DEI. If you move one of them, please write it down here... and do it NOW!


Mirrors

Much work has been done and is being done at the AIRLab on the topic of omnidirectional (machine) vision (sometimes referred to as omnivision). Omnidirectional vision systems use special hardware to overcome the limitations of conventional vision systems in terms of field of view. The approach to this problem that we generally adopt is the use of conventional cameras in association with convex mirrors, i.e. the capturing of the image reflected by a suitably-shaped mirror with a camera. The possibility of designing mirrors with specific geometric properties gives a very useful means to control the geometric behaviour of the whole camera+mirror system.

TODO for someone who knows better ;-) : mirror list

Cable

The complete list of cable for camera connection and/or power is under construction. You can partecipate listing below which cables are you using...

Type length how many? where? project
FireWire 6-6 ? 2 Bicocca (refer to Domenico G. Sorrenti, 2009-11-11) ?
FireWire 6-6 ? 1 on LURCH wheelchair LURCH